Home > Driver Gigabyte > Driver Gigabyte Ga-8ig1000-g

Driver Gigabyte Ga-8ig1000-g

Page 28 8) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. Following is an example for 2 channels (Windows XP): Introduction of audio connectors You may connect CDROM, Walkman or others audio input devices to Line In jack, speakers, earphone or others Page 38 GA-8IG1000 Series Motherboard - 34 -... In order to utilize the front audio header, your chassis must have front audio connector. Source

Page 69: Flash Bios Method Introduction PnP/PCI Configurations Set User Password PC Health Status Save & Exit Setup Frequency/Voltage Control Exit Without Saving ESC: Quit F3: Change Language F8: Dual BIOS Please remove the question mark and restart the system (System will auto-detect the right USB2.0 driver). Page 24: Step 4-2: Connectors & Jumpers Setting Introduction 22) SATA0 / SATA1 11) F_PANEL 23) CI 12) F_AUDIO 24) CLR_CMOS For GA-8IG1000 Pro-G only. To clear CMOS, temporarily shor 1-2 pin. http://www.gigabyte.com/Motherboard/GA-8IG1000-G-rev-3x

USB-ZIP Select your boot device priority by USB-ZIP. Term Of Use Privacy Policy This site uses cookies. Term Of Use Privacy Policy http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Tech.

  • Page 67: Chapter 4 Technical Reference, Bios ™ Introduction BIOS directly.
  • For optional SPDIF cable, please contact your local dealer.
  • For GA-8IG1000 Pro-G only.
  • Then click on the left selection bar and select "4CH Speaker" to complete 4 channel audio configuration.
  • Page 68: Easytune ™ 4 Introduction Moreover, if one well-performed system speed has been tested in EasyTune 4, user can "Save" this setting and "Load" it in next time.
  • Definition +12V Sense GA-8IG1000 Series Motherboard - 22 -...
  • Page 11 CPU, chipset and most of the peripherals.
  • Page 48: Usb Controller SATA controller set to SATA port1.

Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Chipsets, Memory, Cards...etc. Device like printer can be connected to Parallel port; mouse and modem etc can be connected to Serial ports. All rights are reserved. Page 84 Fiber connecting port. 1.

Why? Page 99 Acronyms Acronyms Meaning ACPI Advanced Configuration and Power Interface Advanced Power Management Accelerated Graphics Port Audio Modem Riser Advanced Communications Riser BIOS Basic Input / Output System Central Processing Read the related expansion card's instruction document before install the expansion card into the computer. 2. http://www.driverguide.com/driver/detail.php?driverid=1112618 FAX: +886-2-8912-4003 Tech.

Page 90 GA-8IG1000 Series Motherboard - 86 -... Page 85: Jack-sensing(uaj) Introduction Jack-Sensing(UAJ) Introduction Jack-Sensing provides audio connectors error-detection function. Page 35 For optional IEEE1394 cable, please contact your local dealer. Page 58 Memory Frequency = Host clock X 1.5. 1.33 Memory Frequency = Host clock X 1.33.

Easy Driver Pro updates your Drivers, based on the scan, and matches to the latest most compatible versions. Page 103 Contact Us Taiwan (Headquarters) Japan GIGA-BYTE TECHNOLOGY CO., LTD. For GA-8IG1000 Pro-G only. Download Now for Windows® 10, 8.1, 7, Vista, XP Installation Instructions Click here to begin Easy Driver Pro download Click “Run” (”Save As” if using Firefox) Click “Run” Again Follow on-screen

Page 72 [Enter] to contiune Or [ESC] ot abort... this contact form ECP+EPP Using Parallel port as ECP & EPP mode. Click "@BIOS" item. Support : http://tw.giga-byte.com/TechSupport/ServiceCenter.htm...

GA-8IG1000 Series Motherboard - 46 -... Page 41: Integrated Peripherals, Power Management Setup, Pc Health Status, Select Language, Load Optimized Defaults Change, set, or disable password. Page 79: Channel Audio Function Introduction 2- / 4- / 6- / 8- Channel Audio Function Introduction The installation of windows 98SE/2K/ME/XP is very simple. have a peek here Save & Exit Setup Save CMOS value settings to CMOS and exit setup.

The appropriate response will be provided ASAP. Please insert an AGP 4X/8X card. DIMM OverVoltage Control Normal Set DIMM OverVoltage Control to Normal.

Disabled Disable this function.

After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus controller" under "Device Manager". STEP 3 : Click "Speaker Configuration" and select the "UAJ Function". Page 49: Usb Keyboard Support, Ac97 Audio Onboard H/W 1394 Enable Enable onboard IEEE 1394 function.(Default value) Disable Disable this function. USB Controller Enabled Enable USB Controller. (Default value) Disabled Disable USB Controller.

CONTACT US Please see the last page for details. Please note that any interruption during updating will cause system unbooted. Remove your computer's chassis cover, necessary screws and slot bracket from the computer. 3. Check This Out Definition Signal GA-8IG1000 Series Motherboard - 32 -...

Support : Non-Tech. GA-8IG1000 Series Motherboard - 58 -... Definition +12V +12V 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to The red stripe of the ribbon cable must be the same side with the Pin1.

Third-party brands and names are the property of their respective owners. USB-CDROM Select your boot device priority by USB-CDROM. PCI 4 IRQ Assignment Auto Auto assign IRQ to PCI 4. (Default value) 3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 4. By continuing to browse the site you are agreeing to our use of cookies.

GA-8IG1000 Series Motherboard - 56 -...